GrindDialog 2026: Where the Future of Grinding Begins

A more powerful grinding wheel, a more precise machine, additional sensor technology: each of these developments can improve a grinding process. But none of them can achieve its full impact in isolation. The further individual technologies advance, the more important their interaction becomes. Material, tool, machine, clamping technology, metrology, data and organisation form a manufacturing system. A change in one area affects the conditions in another. These interdependencies were the focus of the GrindDialog. Under the theme “Frontiers of Manufacturing. Beyond what is known.”, the event brought together research and industrial practice. Different disciplines, technological approaches and manufacturing experience converged, not to prescribe a single answer, but to reveal limitations, examine interdependencies and raise new questions. Taken together, the different contributions formed a shared picture: the future of grinding will not be decided solely in the contact zone between the grinding wheel and the workpiece. It will be shaped by the entire manufacturing system.

A Better Metric Does Not Necessarily Mean a Better Process

The GrindDialog used a wide range of approaches to demonstrate just how little a single metric can tell us about the process as a whole. In cryogenic CO₂ cooling, a significant reduction in grinding wheel wear may be accompanied by higher grinding forces. In high-speed belt grinding, increasing the belt speed extends the performance limits, but also affects tool wear, process forces, thermal loads and plant safety requirements. Lower wear is fundamentally positive. So is higher speed. But whether either actually results in a better process can only be determined in conjunction with machine load, process stability and workpiece quality. Technological progress is rarely one-dimensional. What matters is not which individual value has been improved, but what that improvement does to the process as a whole.

There Is Still Much We Do Not Know About Familiar Processes

Two very different approaches revealed how much development potential remains in established grinding processes. Path Controlled Intermittent Grinding, or PCIG, does not primarily change the machine or the tool. Instead, it changes the way the tool engages with the workpiece. Deliberately controlled phases of contact and retraction open up new possibilities for considering thermal load and productivity together. Grinding wheel conditioning addresses the process at a different point. The dressing conditions influence the wheel’s topography, which in turn determines its process behaviour and the achievable surface quality. What initially appears to be a preparatory step thus becomes an essential part of process design. PCIG changes the nature of the engagement. Grinding wheel conditioning changes the conditions under which that engagement takes place. Both approaches lead to the same conclusion: established grinding processes are far from fully developed. The next stage in the evolution of grinding will therefore not emerge from new technologies alone. It will also come from a deeper understanding of relationships that are already familiar.

New Materials Require New Process Solutions

The example of cobalt-free and cobalt-reduced cemented carbides demonstrated that the implications of a new material extend far beyond its composition. Alternative binder systems affect not only the properties of the material, but also its behaviour during grinding, including process forces, tool wear, surface quality and process control. A new material only creates industrial value if its advantages can be combined with reliable and cost-effective machining. Material development and the grinding process must not be considered separately. The material changes the process. The process determines whether the material can become an industrially viable solution.

Precision Is Not Created on a Data Sheet

The interaction between the contributions on linear guides, clamping technology and fixture intelligence demonstrated how many factors must come together before technical precision can be measured on the workpiece. Greater rigidity, reduced motion errors and more precise linear guides create important conditions for machining. Whether these advances ultimately translate into improved results on the workpiece, however, depends on their interaction with all other influencing factors. Clamping technology is one of these factors. Clamping force, workpiece positioning, contact conditions, rigidity, damping and repeatability all have a direct impact on the grinding process. Intelligent clamping systems monitor the workpiece diameter, clamping status and correct positioning. Automated clamping device changes also enable the unattended production of a wide variety of workpieces over extended periods. Nor does wear have to be regarded solely as an unavoidable source of disruption. If the geometry of a worn dressing tool is measured and its path adjusted accordingly, a progressive change becomes a process variable that can be compensated for. Precision is not created by a single machine component or on a data sheet. It is created on the workpiece. To achieve it, the machine, tool, clamping technology and process control must interact in a controlled manner under real machining conditions.

More Data Does Not Necessarily Mean More Process Knowledge

Intelligent process analysis demonstrated particularly clearly that more data does not automatically result in more process knowledge. Modern grinding machines already provide extensive information about their condition and the process currently taking place. Additional sensor technology can expand this data set. The crucial question, however, is not how much data can be collected. It is which information is required to make better process decisions. Intelligent process analysis therefore begins with the data already available in the machine. Additional sensors are used where relevant process states cannot be identified with sufficient reliability from the existing information. Acoustic signals, for example, can provide indications of the tool condition, spark activity or changes to the workpiece surface. Their value, however, does not lie in the signal itself. It only emerges when the signal can be translated into a reliable conclusion and subsequently into an appropriate response. Data describes a condition. Process knowledge explains it.

Productivity Does Not End with Machining Time

The topics of metrology and digital continuity demonstrated how quickly an improvement in one part of the process can lose its impact at the next interface. A grinding process may be shortened by a few seconds. But if the subsequent quality decision takes several minutes, the actual productivity gain remains limited. The relevant process therefore does not end with the final grinding contact. Metrology close to the machine reduces more than measurement time. Above all, it shortens the route between machining, measuring, deciding and responding. Deviations become visible sooner, corrections can be made more quickly, and metrology evolves from a downstream inspection step into an integral part of the process chain. The same principle applies to the flow of information. Design, programming, manufacturing and quality control have long worked with digital data. Yet repeated data entry, differences in interpretation and discontinuities between systems still occur at their interfaces. Digital continuity therefore does not mean connecting as many systems as possible. It means making the right information available where it is needed for the next step in the process.

Autonomy Requires More Process Expertise, Not Less

The contributions on simulation, digital twins and artificial intelligence demonstrated how far decisions can already be moved upstream of the physical process. Simulations make it possible to evaluate geometries and process conditions before committing material, tools or machine time. Digital twins connect virtual models with real machine and process conditions. This creates a protected testing environment for self-learning systems, in which potential decisions can first be evaluated virtually before they influence the physical process. At the same time, robotics is advancing from predefined motion sequences towards more flexible systems incorporating machine vision, combined sensor technology, intelligent grippers and dual-arm concepts. This brings applications within reach that have previously been difficult to automate due to high product diversity or small batch sizes. Yet identifying a pattern is not the same as understanding its cause. Nor is a prediction sufficient justification for intervening in a process. It must be possible to understand why a relationship exists, how reliable it is and within which boundaries a model can operate. Autonomy does not begin where process knowledge becomes unnecessary. The opposite is true: the more autonomously a manufacturing system is expected to operate, the deeper the underlying process understanding must be.

The Decisive Minutes Are Often Found Between Processes

A closer look at setup times, information flows and practical experience showed that the next productivity limit is not necessarily located within the machine. With every further optimisation of the grinding process, the time before, after and between machining operations becomes more important. Setup procedures, workpiece changes, measurement processes, missing information and organisational coordination all influence how productive a manufacturing operation really is. Even the most powerful machine cannot realise its full potential if the flow of materials or information comes to a standstill. There is also a form of process knowledge that cannot be found in any machine control system: the day-to-day experience of employees. The shop floor reveals where improvisation is required, where information arrives too late and which processes are unnecessarily complicated. This knowledge is not always reflected in performance indicators or machine data. Nevertheless, it is indispensable when improving real production processes. The technological and organisational perspectives lead to the same conclusion: technical performance only translates into productivity when the processes surrounding the machine also function effectively. Simply collecting information is therefore not enough. Not in the case of a sensor signal. Not in the case of a measured value. Not in the case of feedback. A process only improves when an observation leads to a better decision and that decision results in an effective change.

Different Perspectives, One Shared Picture

What connects the contributions to the GrindDialog is not a single technology. It is the recognition that decisive advances are increasingly being made at the interfaces. Grinding strategies, materials, machine components, clamping technology, data, simulation and organisation did not converge into a single answer. Taken together, however, they revealed where the decisive questions now lie: in the interaction between technologies and their impact on the manufacturing system as a whole. For grinding, this means that the contact zone remains at the heart of the process. But what happens there is determined by far more than the grinding wheel and the workpiece. Material, machine, clamping technology, sensors, metrology, software and organisational processes all contribute to the result. Process expertise therefore means understanding these interdependencies and bringing them under technical control. The GrindDialog creates a space for this exploration. Science and industry examine the same challenges from different perspectives, compare practical experience with research findings and connect topics that are often treated separately in day-to-day manufacturing. The aim is not to leave after two days with a single answer, but with a more precise understanding of the interdependencies and better questions for the next stage in the evolution of manufacturing.